Welcome, Guest. Please login or register.

Login with username, password and session length
 

News:



Recent Posts

Pages: 1 ... 3 4 [5] 6 7 ... 10
41
Electroacoustics Toolbox / Oscilloscope: Crest & RMS & Peak
« Last post by audiot1949 on November 01, 2015, 01:15:20 PM »
It seems, that Crest & RMS & Peak are calculated from the start to the end of the recorded thread.
Is this really so intended or shouldn’t these values calculated between Cursor 1 and 2?
42
Electroacoustics Toolbox / Nice to have: “waterfall” diagram
« Last post by audiot1949 on October 31, 2015, 10:48:13 AM »
(this should be not mixed up with a “spectrogram”)
This waterfall diagram gives normally in the x-axis the frequency, in the z-axis the level and in the y-axis the time and shows the “decay” of the sound.
It is e.g. calculated by a sweep like produced by the excitation of the DFFT and can be used in rooms in the far field to detect modes and resonances. In measuring loudspeakers (near field) it can be used to detect resonances.
(please see to enclosed example)
43
Electroacoustics Toolbox / Dual FFT Analyzer: Excitation „misleading“ Pre-sends
« Last post by audiot1949 on October 31, 2015, 10:47:16 AM »
It seems that the setting of the values of „Pre-sends“ has no influence.
The excitation runs nonstop when you start the machine regardless whether you enter 0 or 99. In some cases it makes sense to take single shots only.
In my opinion it would make more sense either to store automatically the latest measurement after the given pre-send # is achieved OR the function stops when the # is achieved. Then you can decide to store it or start a new measurement.
44
Electroacoustics Toolbox / Spectrogram 3D Surface: missing x/y/z scale
« Last post by audiot1949 on October 31, 2015, 10:46:49 AM »
You can rotate the diagram but the scales are missing.
The shown scales respond to the 2D diagram and not to the 3D.
Please have a look at the screenshot.
45
Well, they are in the collected measurement data as values. To have it as selectable curves too would be nice!
46
Electroacoustics Toolbox / Room Tools Analyzer: General
« Last post by audiot1949 on October 31, 2015, 10:45:19 AM »
This is really, really a great and awesome tool!
Like it very much, but you should provide a “cooking recipe” with a block diagram and screen shots how to set it up and get it work.
It took me hours to make the setup and get sensible results because of missing info.
Ben, thank you again, without your detailed help I couldn’t have got it work properly!
47
Electroacoustics Toolbox / Re: nan dB
« Last post by FaberAST on October 26, 2015, 08:26:51 PM »
"nan" stands for "not a number" and indicates that some invalid arithmetic operation occurred (like dividing zero by zero).
48
Electroacoustics Toolbox / nan dB
« Last post by brianf7408 on October 16, 2015, 06:41:46 PM »
Occasionally when attempting to take a THD, SNR, etc., I get the characters "nan".  What does that stand for and what can i do about it?
49
SignalScope Pro / Re: THD measurement
« Last post by FaberAST on October 16, 2015, 01:43:00 PM »
Quote
Am I correct in assuming that the number of spectral lines is equivalent to the number of bins?
Yes. Each line represents one bin.
50
SignalScope Pro / Re: THD measurement
« Last post by brianf7408 on October 16, 2015, 01:21:48 PM »
Am I correct in assuming that the number of spectral lines is equivalent to the number of bins?
Pages: 1 ... 3 4 [5] 6 7 ... 10