Welcome, Guest. Please login or register.

Login with username, password and session length
 

News:



Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - PeterHa

Pages: [1]
1
SoundMeter / Suggestions for Sig Gen
« on: November 20, 2009, 09:25:50 PM »
The Sig Gen capabilities in SoundMeter are a very nice bonus in an already excellent app.

I have a couple of suggestions for enhancements:

Frequency of sinusoidal tone.
It would be great to have an option for the frequency slider to step the frequency in discrete 1/3-octave intervals. The frequency points should be exact 1/3-octave band centre frequencies, e.g. 251.2 Hz rather than 250 Hz.
[Another option might be for musical intervals based on A = 440 Hz, although this wouldn't be of particular interest to me.]

UI suggestions.
Delete the label 'Type:'. It's (pretty much) obvious what the buttons do.
Maybe set the resolution of the slider range limits to 1 Hz rather than 0.001 Hz? I would tend to have the slider range set rather wide (e.g. 125 Hz to several kHz), although I can see that others might want extremely fine resolution.

Signal types.
Would be nice to have square wave and other noise colours (and band limits on the noise), but I think that the current Sig Gen capabilities are already pretty nice for a sound level meter app!  :-D

Peter

2
SoundMeter / First impressions of the UI
« on: November 20, 2009, 08:55:09 PM »
Ben,

I just bought SoundMeter 1.6 (r388) for my iPhone 3G, and I'm very impressed. It seems like the best SLM app for iPhone.

I haven't delved very deeply into it today - I've just been using the iPhone's built-in mic.

I have a few first impressions about the main SLM UI in portrait orientation...

Main (large-font) digital sound level indicator.
I actually think that the display update rate is a bit too fast! It doesn't need to update any (or much) faster than once per second. I found myself immediately switching to Slow time-weighting, whatever the noise is.

Smaller digital indicators.
These are just right: great to see maximum and peak levels displayed.

Quantity.
I don't think that this line is even necessary. I don't know whether the area to the left of the large display is used for anything other than the 'Clip' indicator, but it seems to me that this area could be used for the indication of the quantity being measured. The indication should be as simple as LAeq, LCF etc, because the selection buttons at the foot of the screen show the full text of the weighting and response. On this part of the display, I would use Z to indicate the "Flat" frequency weighting because it seems that you really are implementing Z weighting and not just Flat weighting. If text on the iPhone doesn't allow subscripts, there could be a little graphic that showed the letters with the subscripts.
So the overall effect would be like: LAF = 72.3

Elapsed time.
Increments of 0.01 s? There's no need to have increments that are finer than 1 s. No one can control the meter to 0.01 s and the flicker of the last two digits is an unnecessary distraction for the user.
Could you put two digits in the number of seconds (e.g. 1m 07s instead of 1m 7s), please?

Bar graph.
Beautiful! But there's no need to have a decimal place in the level labels. It would be clearer with just 20 ... 40 ... etc. It would also be nice if the quantity label here could be in the format LAF, if that's possible. Would the quantity label be better placed at the left edge of the bar graph rather than underneath? This would save all the unused space to the left and right of the quantity label. The bar graph would be narrowed slightly, but it would still have the same visual appeal.

Function buttons.
I'm going to suggest that you could delete the labels 'Level Type:', 'Weighting:', and 'Response:'. I think that anyone willing to pay the purchase price for this app would be able to figure out what the function buttons do without the labels.

And in landscape orientation...
Similar comments to the above. Move the quantity label for the bar chart to the top or bottom of the bar chart and run it horizontally like all the rest of the text.

Peter

3
SignalScope Pro / Question about SLM capability
« on: November 06, 2009, 02:13:33 PM »
I'm interested in buying SignalScope Pro for iPhone, but I'd like to check about its capability as a sound level meter before purchasing.

The website indicates that the fractional-octave-band analyzer mode includes measurement of frequency-weighted time-averaged sound level (eg L_Aeq) and maximum and peak levels, but I couldn't see where these are displayed and controlled on the example screenshot. Could you show a screenshot of these facilities, please?

Does the app indicate C-weighted peak sound level?

What are the minimum and maximum frequencies for the 'flat' frequency weighting? Does it cover 10 Hz to 20 kHz as in the IEC 61672-1 specification for frequency weighting Z?

My personal preference would be to buy your SoundMeter app and then use in-app purchasing to upgrade later to SignalScope Pro. Is that possible, or planned?

Thanks in advance,
Peter

Pages: [1]